MS-2000 3D parts
Printer: Flashforge Adventurer 5M, PLA. Designed from datasheets; re-checked with calipers when the parts arrive.
- 3DTurret, every componentdone
The turret with every printed and bought part in place. Tap a name to highlight it, Explode to pull it apart, Head or Base to zoom in.
- 3DWhole setup, assembleddone
Everything together: the turret, the black backdrop on its feet, the dowel with the pendulum pivot, the stuffed mosquito with its glowing pod hanging 3 ft from the camera, the wand, the ribbon cable, and the laser beam. Zoom to the turret or the mosquito with one tap.
- CBought parts, measureddone
Every bought part as a stand-in model. Numbers marked estimate or photo get checked with calipers when the parts arrive.
- P1Base shelldone
142 x 133 x 67, Rev B (MOC-004). Front window for the micro:bit LEDs, lift-out slot, USB-C charge port and power switch window on the right, speaker grille and laser arm switch on the back. About 169 g.
- P1Floor platedone
Rev B (MOC-004). Board posts, power bank cradle with strap slots, and the stand the power switch sits on. Four screws up into the shell. Board hole spacing is from a photo. About 76 g.
- P2Turntable + tilt yokedone
One print: 74 mm disc on the pan servo horn, two uprights 39 mm to the tilt axis. Tilt servo on the right upright, pivot pin bushing and printed tilt stops (35 up, 30 down) on the left. Cable arch at the back. About 39 g.
- P3Pivot pindone
Left-side tilt axle. An M2 screw clamps it to the head; it turns in the upright.
- P4Camera and laser headdone
Closed frame 61 mm wide. HuskyLens on two M3 screws, lens forward, screen readable from behind. Laser 38 mm under the lens in a plastic pinch clamp, toed up 2.4 degrees so the dot meets the camera line at 3 ft (13 mm off at 2 ft, 10 mm off at 4 ft). Horn pocket right, pivot socket and stop finger left. About 11 g. The top bar is a 53 mm bridge: if it sags, print the head on its back.
- P5Wand handledone
56 x 119 mm paddle. micro:bit face up; M2 screws through its big rings clamp the cable wires (P0 sensor, P1 eyes, 3V, GND) with no soldering. 2xAAA pack behind it. A V under it centers rods from 9 to 30 mm; the rear zip ties go over the pack and under the rod. About 50 g.
- P6Mosquito sensor pod, frontdone
Print in WHITE. A 40 mm face 0.8 mm thick: the laser dot anywhere on it makes the whole cup glow, so hits count even when the dot lands up to 17 mm off center. Eye bar on top with two red LEDs facing the turret (outside the cup, so the eyes never set off the sensor), cable slot, fishing-line tab. About 8 g.
- P6Mosquito sensor pod, backdone
Plugs into the front. Holds the light sensor facing into the cup; wires and the two 220 ohm resistors go in the open back. Sew the four lugs or strap it to the stuffed mosquito. About 9 g.
- P7Pendulum pivotdone
Clamps on the end of a 1/4 in dowel. The line loops over the peg; rim notches mark 0, 10, 20, 30 degrees each way and the round holes count the tens. About 14 g.
- P7Backdrop clipdone
Pushes onto the top edge of the 5 mm foam board and holds the dowel straight out toward the turret.
- P7Backdrop foot (print 2)done
Holds the foam board upright. Ridges in the slot grip the board.
- P8Cable clipsdone
8 clips that ride on the fishing line and hold the ribbon cable beside it, plus 3 that snap on a 3/8 in dowel.
- Plate 1Base shelldone
any color (pink on the site). 1 piece, 3h 13m 24s, 131 g. Adventurer 5M 0.4 nozzle, Generic PLA, 0.2 mm layers, 3 walls, 15% gyroid, 5 mm brim, no supports.
- Plate 2Floor plate and one backdrop footdone
any color. 2 pieces, 1h 53m 38s, 72 g. Adventurer 5M 0.4 nozzle, Generic PLA, 0.2 mm layers, 3 walls, 15% gyroid, 5 mm brim, no supports.
- Plate 3Turntable, head, pivot pin, wand, pod backdone
any color. 5 pieces, 3h 33m 45s, 77 g. Adventurer 5M 0.4 nozzle, Generic PLA, 0.2 mm layers, 3 walls, 15% gyroid, 5 mm brim, no supports.
- Plate 4Pod front and cable clipsdone
WHITE PLA. 2 pieces, 34m 22s, 11 g. Adventurer 5M 0.4 nozzle, Generic PLA, 0.2 mm layers, 3 walls, 15% gyroid, 5 mm brim, no supports.
- Plate 5Pendulum pivot, backdrop clip, second footdone
any color. 3 pieces, 1h 26m 27s, 44 g. Adventurer 5M 0.4 nozzle, Generic PLA, 0.2 mm layers, 3 walls, 15% gyroid, 5 mm brim, no supports.